Characteristics

Altitude Operating Conditions

The characteristics in the table below apply to the modules BMX DRA 0805 and BMX DRA 0805H for use at altitude up to 2000 m (6560 ft). When the modules operate above 2000 m (6560 ft), apply additional derating.

For detailed information, refer to chapter Operating and Storage Conditions.

General Characteristics

This table presents the general characteristics for the BMX DRA 0805 and BMX DRA 0805H modules:

Module type			Relay outputs for alternating and direct current
Operating temperature	BMX DRA 0805		0...60 ºC (32...140 ºF)
	BMX DRA 0805H		-25...70 ºC (-13...158 ºF)
Rated voltage	Direct		24 VDC
	Alternating		24...240 VAC
Voltage range	Direct		10...34 VDC
	Alternating		19...264 VAC (47...63 Hz)
Thermal current			3 A
Minimum switching load			5 VDC / 10 mA
Alternating current load in resistive mode (AC12)	Voltage		24 VAC	48 VAC	100...120 VAC	200...240 VAC
	Power		50 VA⁽⁵⁾	50 VA⁽⁶⁾ 110 VA⁽⁴⁾	110 VA⁽⁶⁾ 220 VA⁽⁴⁾	220 VA⁽⁶⁾
	Maximum Power of Hardened module at 70°C (158°F)		30 VA⁽⁵⁾	30 VA⁽⁶⁾ 66 VA⁽⁴⁾	66 VA⁽⁶⁾ 132 VA⁽⁴⁾	132 VA⁽⁶⁾
Alternating current load in inductive mode (AC15)	Voltage		24 VAC	48 VAC	100...120 VAC	200...240 VAC
	Power		24 VA⁽⁴⁾	10 VA⁽¹⁰⁾ 24 VA⁽⁸⁾	10 VA⁽¹¹⁾ 50 VA⁽⁷⁾ 110 VA⁽²⁾	10 VA⁽¹¹⁾ 50 VA⁽⁹⁾ 110 VA⁽⁶⁾ 220 VA⁽¹⁾
	Maximum Power of Hardened module at 70°C (158°F)		14.4 VA⁽⁴⁾	6 VA⁽¹⁰⁾ 14.4 VA⁽⁸⁾	6 VA⁽¹¹⁾ 30 VA⁽⁷⁾ 66 VA⁽²⁾	6 VA⁽¹¹⁾ 30 VA⁽⁹⁾ 66 VA⁽⁶⁾ 132 VA⁽¹⁾
Direct current load in resistive mode (DC12)	Voltage		24 VDC
	Power		24 W⁽⁶⁾ 40 W⁽³⁾
	Maximum Power of Hardened module at 70°C (158°F)		14.4 W⁽⁶⁾ 24 W⁽³⁾
Direct current load in inductive mode (DC13) (L:R=60 ms)	Voltage		24 VDC
	Power		10 W⁽⁸⁾ 24 W⁽⁶⁾
	Maximum Power of Hardened module at 70°C (158°F)		6 W⁽⁸⁾ 14.4 W⁽⁶⁾
Response time	Activation		< 10 ms
	Deactivation		< 8 ms
Built-in protection	Against inductive over voltage in AC modes		None. Fit an RC circuit or a ZNO type over voltage limiter in parallel on each output appropriate to the voltage in use.
	Against inductive over voltage in DC modes		None. Fit a discharge diode on each output.
	against short-circuits and overloads		None. Fit a fast-blow fuse of 3 A for each relay.
Reliability	MTBF for continuous operation in hours at ambient temperature 30°C (86°F)		2 119 902
Power dissipation			2.7 W max.
Dielectric strength (at 50/60 Hz for 1 min.)			2000 V actual
Resistance of insulation (at 500 VDC)			>10 MΩ
Power supply consumption	3.3 V	Typical	79 mA
		Maximum	111 mA
	24 V relay⁽¹²⁾	Typical	51 mA
		Maximum	56 mA
(1):0.1 x 10⁶ cycles, (2): 0.15 x 10⁶ cycles, (3): 0.3 x 10⁶ cycles, (4): 0.5 x 10⁶ cycles, (5): 0.7 x 10⁶ cycles, (6): 1 x 10⁶ cycles, (7): 1.5 x 10⁶ cycles, (8): 2 x 10⁶ cycles, (9): 3 x 10⁶ cycles, (10): 5 x 10⁶ cycles, (11): 10 x 10⁶ cycles, (12): all channels at 1.