Details of T_SAP10_STD-type IODDT Explicit Language Objects

At a Glance

The tables below present the T_SAP10_STD-type IODDT explicit objects that are applicable to all Fipio standard profiles.

Execution Indicators of an Explicit Exchange: EXCH_STS

The table below presents the meanings of the exchange control bits of the channel EXCH_STS (%MW\2.e\0.m.c.0).

Standard symbol	Type	Access	Meaning	Address
STS_IN_PROGR	BOOL	R	Reading of channel status words in progress.	%MW\2.e\0.m.c.0.0
CMD_IN_PROGR	BOOL	R	Current command parameters exchange in progress.	%MW\2.e\0.m.c.0.1
ADJ_IN_PROGR	BOOL	R	Adjustment parameters exchange in progress.	%MW\2.e\0.m.c.0.2
RECONF_IN_PROGR	BOOL	R	Reconfiguration in progress.	%MW\2.e\0.m.c.0.15

Explicit Exchange Report: EXCH_RPT

The table below presents the meaning of the exchange report bits EXCH_RPT (%MW\2.e\0.m.c.1).

Standard symbol	Type	Access	Meaning	Address
STS_ERR	BOOL	R	Reading error for channel status words.	%MW\2.e\0.m.c.1.0
CMD_ERR	BOOL	R	Error during command parameter exchange.	%MW\2.e\0.m.c.1.1
ADJ_ERR	BOOL	R	Error during adjustment parameters exchange.	%MW\2.e\0.m.c.1.2
RECONF_ERR	BOOL	R	Error when configuring channel.	%MW\2.e\0.m.c.1.15

Standard Channel Faults, CH_FLT

The status word CH_FLT provides information on all slaves on the AS-i communication channel.

This 16-bit word contains diagnostics information for the TBX SAP 10 module and diagnostics information relating to exchanges with the TBX SAP 10 across the Fipio network.

The following table shows the meaning of the bits of the status word CH_FLT (%MW\2.e\0.m.c.2).

Standard symbol	Type	Access	Object	Meaning	Function
-	BOOL	R	%MW\2.e\0.m.c.2.0	bit 0: not used.	Statuses generated by the TBX SAP 10
ASI_CONF_FLT	BOOL	R	%MW\2.e\0.m.c.2.1	AS-i bus configuration fault.
SLAVE0_FLT	BOOL	R	%MW\2.e\0.m.c.2.2	slave present at address 0 on AS-i bus.
ASI_SUPPLY_FLT	BOOL	R	%MW\2.e\0.m.c.2.3	AS-i power supply missing.
INTERNAL_FLT	BOOL	R	%MW\2.e\0.m.c.2.4	internal module fault (failure).
CONF_FLT	BOOL	R	%MW\2.e\0.m.c.2.5	hardware configuration fault.
COM_FLT	BOOL	R	%MW\2.e\0.m.c.2.6	communication fault with PLC.
APPLI_FLT	BOOL	R	%MW\2.e\0.m.c.2.7	application fault.
PLC_CONF_FLT	BOOL	R	%MW\2.e\0.m.c.2.8	PLC configuration fault.	Statuses generated by the PLC
MOD_MISSING	BOOL	R	%MW\2.e\0.m.c.2.9	module missing.
MOD_NOT_OP	BOOL	R	%MW\2.e\0.m.c.2.10	module not operational.
MOD_FLT	BOOL	R	%MW\2.e\0.m.c.2.11	module fault.
PLC_HW_FLT	BOOL	R	%MW\2.e\0.m.c.2.12	internal fault, PLC hardware fault.
PLC_SYS_FLT	BOOL	R	%MW\2.e\0.m.c.2.13	internal fault, PLC system fault.
FIP_COM_FLT	BOOL	R	%MW\2.e\0.m.c.2.14	dialog fault, Fipio communication fault.
PRM_FLT	BOOL	R	%MW\2.e\0.m.c.2.15	dialog fault, TBX SAP 10 parameter error.

ASI_CONF_FLT corresponds to the error bit %MW\2.e\0.0.0.2.1, and indicates a discrepancy between the actual AS-i bus configuration and the reference configuration. If the TBX SAP 10 module is in:
- Protected mode, the slaves at the addresses concerned are no longer active.
- Configuration mode, this fault is indicated but the slaves at the addresses concerned remain active.

SLAVE0_FLT corresponds to word bit %MW\2.e\0.0.0.2.2, and indicates the presence of a slave at address 0 on the AS-i bus. This has no effect on AS-i bus operation, but generates an AS-i bus configuration error.
- When this bit is at 1, it is not possible to switch from Configuration to Protected mode.

ASI_SUPPLY_FLT corresponds to word bit %MW\2.e\0.0.0.2.3, and indicates missing AS-i bus power supply.

When this bit is at 1:
- All the outputs of the AS-i bus are set to 0,
- All the inputs of the AS-i bus sent back to PLC are equal to 0.

Slave Parameters, PRM SLV

The following table presents the language objects that contain the value of the parameters sent to the AS-i intelligent slaves using the TBX SAP 10 module.

Standard symbol	Type	Access	Meaning	Address
PRM_SLV_0 to PRM_SLV_31	INT	RW	Parameters of slave 0 to slave 31. Contains the reply (value of the parameters sent) from the last slave parameterized. This allows you to verify via Control Expert that the slave has received them correctly.	%MW\2.e\0.m.c.4 to %MW\2.e.\0.m.c.35